การวาดส่วนที่รื้อถอน
การสั่งซื้อสินค้าแบบขนาน
(A และ B สามารถจัดแนวได้ภายใน 0.01 ไม่ว่าจะกี่ชิ้นก็ตาม)
หากคำต่อท้ายหมายเลขการผลิต (ติดกับกล่องด้านนอกและตัวหลัก) เป็นอักษรเดียวกัน ดังนั้น สินค้าจะขนานกันกี่ชิ้นก็ได้ (สำหรับบล็อคนำมาตรฐาน) ไม่มีค่าใช้จ่ายสำหรับผลิตภัณฑ์แบบขนาน
- เมื่อซื้อครั้งแรก
สั่งซื้อผลิตภัณฑ์สเปคที่ตรงกัน (ต่อท้าย G) เมื่อสั่งซื้อให้ระบุความกว้างร่องของเครื่องที่คุณใช้
- หากต้องการสั่งซื้อเพิ่มเติม
ติดต่อเราด้วยตัวอักษรต่อท้ายของหมายเลขการผลิต (ประทับตราบนแผ่นป้ายชื่อ) และความกว้างของไกด์บล็อคของปากกาจับที่คุณมี
การเพิ่มการเปิดกราม
สามารถเปิดกรามขนาดใหญ่ได้โดยการเปลี่ยนตำแหน่งแผ่นกราม
- การเปิดกรามขึ้นอยู่กับตำแหน่งการติดแผ่นกราม
![]() |
![]() |
![]() |
![]() |
|
LT100M | 0 – 102 | 48 – 150 | 115 – 217 | 163 – 265 |
LT125M | 0 – 112 | 56 – 168 | 140 – 252 | 196 – 308 |
LT150M | 0 – 143 | 63 – 206 | 160 – 303 | 223 – 366 |
LT200M | 0 – 190 | 85 – 275 | 199 – 389 | 284 – 474 |
LT250M | 0 – 248 | 110 – 358 | 233 – 501 | 366 – 614 |
- วิธีการเคลื่อนย้ายแผ่นกราม
มาตรฐานความแม่นยำ (ความแม่นยำคงที่)
No. | Inspection Points (per 100 mm) | Former JIS Standard (O Grade) |
Nabeya SPEC |
1 | Parallelism between bottom surface of main body and sliding surface | 0.015 | 0.010 |
2 | Perpendicularity between jaw plate and sliding surface (smaller than right angle) | 0.030 | 0.015 |
3 | Perpendicularity between T-slot and jaw plate surface of stationary jaw side. | 0.015 | 0.010 |
4 | Parallelism between T-slot and jaw plate surface of stationary jaw side. | 0.015 | 0.010 |
5 | Parallelism between bottom surface of rotating table and sliding surface | 0.020 | 0.015 |
6 | Parallelism between the bottom surface and top surface of the rotating table | – | 0.010 |
(Clamping Accuracy) | |||
7 | Parallelism between top surface of clamped test block and bottom surface of main body | 0.020 | 0.015 |
8 | Parallelism between top surface of clamped test block and bottom surface of rotating table | 0.030 | 0.020 |
9 | Lift-up of top surface of test block when clamped | 0.030 | 0.015 |